RailFX cable railing:
Cables and fittings are installed flush and inside the posts, and come pre-cut in several lengths.
-
RailFX Cable Railing: Pre-Fitted Cable Railing Sections for Through-Post Setup
$ 60.00 – $ 150.00 Select options This product has multiple variants. The options may be chosen on the product page
Cable tops are available in 8' sections, and are available in different profiles
Each top rail requires splices wherever top rail is seamed, including corners and joints near stairs.
Wide rectangular top rail is commonly used on horizontal sections, when a drink rail deck board is not being installed.
-
RailFX Cable Railing Top End Plate
$ 29.99 Select options This product has multiple variants. The options may be chosen on the product page -
RailFX Series 200 Flat Top Cable Rail
$ 198.30 Select options This product has multiple variants. The options may be chosen on the product page -
Splices for 200 Flat Top Rail for RailFX Cable Railing
$ 14.99 – $ 44.96 Select options This product has multiple variants. The options may be chosen on the product page
A different top rail can be installed so that a deck board can be used as a drink rail or cocktail rail across the top.
-
RailFX 400 Cocktail Rail Cable Railing Top
$ 198.30 Select options This product has multiple variants. The options may be chosen on the product page -
Splices for RailFX 400 Cocktail Top Rail
$ 14.99 – $ 44.96 Select options This product has multiple variants. The options may be chosen on the product page
A narrower square top rail is used when a graspable handrail is required, like on stairs or ramps. Different mounting brackets are required on top of rail posts to attach the top rail to the posts.
-
RailFX 250 Series Graspable Top Rail
$ 164.91 Select options This product has multiple variants. The options may be chosen on the product page -
RailFX Crossover Post Bracket for 250 Top Rail
$ 46.47 Select options This product has multiple variants. The options may be chosen on the product page -
RailFX End Plate for 250 Top Rail
$ 29.99 Select options This product has multiple variants. The options may be chosen on the product page -
Splices for Series 250 Graspable Top Rail for RailFX Cable Railing
$ 1.50 – $ 17.99 Select options This product has multiple variants. The options may be chosen on the product page
Surface-Mounted Railing posts
Posts on cable railing should be installed no more than 55" apart. 10 cables are needed when setting up a 36" high railing section.
Intermediate posts are used in the middle of straight runs, on corners where two posts are used, and when a stair rail transitions to a horizontal section that continues in line with the stair railing.
Single corner posts are used when continuously running cable at a 90 degree angle, and a single surface-mounted post is required (not available with fascia mount posts)
Slotted posts are used on middle posts on straight runs of stairs, where flexibility on cable angle is needed to match the stair angle.
End posts are used when cable stops at a house wall, end of a cable run, or where an angle is too sharp to continuously run a cable around the corner.
-
Aluminum Surface-Mount Post for RailFX Cable Railing
$ 142.42 – $ 215.85 Select options This product has multiple variants. The options may be chosen on the product page
Fascia-Mounted Railing posts
Intermediate posts are used in the middle of straight runs, on corners where two posts are used, and when a stair rail transitions to a horizontal section that continues in line with the stair railing.
Slotted posts are used on middle posts on straight runs of stairs, where flexibility on cable angle is needed to match the stair angle.
End posts are used when cable stops at a house wall, end of a cable run, or where an angle is too sharp to continuously run a cable around the corner.
Fascia-mount posts are mounted to the outside of the deck, on the outer side of the deck framing.
Straight brackets are used in posts along flat surfaces like the middle of a deck, or halfway down stair runs.
Corner brackets are used when turning an outside 90 degree corner.
-
Aluminum Fascia Mount Post for RailFX Cable Railing
$ 110.00 – $ 165.00 Select options This product has multiple variants. The options may be chosen on the product page -
Fascia Mount Brackets for RailFX Cable Railing Post
$ 120.00 – $ 254.87 Select options This product has multiple variants. The options may be chosen on the product page -
Post End Cap for RailFX Cable Railing Post
$ 15.25 Select options This product has multiple variants. The options may be chosen on the product page -
Screw Cap Covers for RailFX Cable Railing Posts
$ 0.55 – $ 6.22 Select options This product has multiple variants. The options may be chosen on the product page -
Stainless 1″ Screws for RailFX Fascia Mount Brackets
$ 0.59 Add to cart -
Stainless Lag Bolts for mounting RailFX Cable Post
$ 2.35 – $ 6.45 Select options This product has multiple variants. The options may be chosen on the product page
Fascia-mount posts can also be installed with lag screws horizontally through the post and into the deck rim, using the following parts:
-
Fascia Post Bottom Plate
$ 18.00 Select options This product has multiple variants. The options may be chosen on the product page -
Flush Mount Fascia Post Kit for RailFX Cable Railing Post
$ 28.48 Select options This product has multiple variants. The options may be chosen on the product page -
Post End Cap for RailFX Cable Railing Post
$ 15.25 Select options This product has multiple variants. The options may be chosen on the product page -
Screw Cap Covers for RailFX Cable Railing Posts
$ 0.55 – $ 6.22 Select options This product has multiple variants. The options may be chosen on the product page -
Stainless Lag Bolts for mounting RailFX Cable Post
$ 2.35 – $ 6.45 Select options This product has multiple variants. The options may be chosen on the product page
Other parts
Posts come standard with vinyl caps to cover the screws, but post base skirts can be added for a cleaner look
-
Post Base Cover/Skirt for RailFX Cable Railing Posts
$ 24.80 Select options This product has multiple variants. The options may be chosen on the product page
Unusual angle splices (other than 90 degree and 135 degree) require flat aluminum pieces to be custom-cut and placed inside the top rail to keep the splice tight and even. These pieces can be cut from the part below:
-
Internal Post Brace for RailFX Cable Post
$ 6.82 – $ 7.87 Select options This product has multiple variants. The options may be chosen on the product page
Touch-up paint is also available for cleaning up cuts, splices, and scratches
-
RailFX Touch-Up Paint
$ 21.00 Select options This product has multiple variants. The options may be chosen on the product page
